Planning Instructions Fire Alarm System EBL512 G3 V1.1.x

168 Pages·2011·3.15 MB·English

by  Jan Pettersson

Planning Instructions
MEW01351
Revision -

Fire Alarm System EBL512 G3
V1.1.x

Author: Jan Pettersson Date of issue: 2011-02-11 Date of rev:
This page has deliberately been left blank.
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
Table of contents
1 Introduction________________________________ 8
2 Definitions / Explanations ___________________ 10
2.1 PEWN AB _______________________________________ 10
2.2 Alarm points _____________________________________ 10
2.2.1 Smoke detector _______________________________ 10
2.2.2 Sensor ______________________________________ 10
2.2.3 Analog detector _______________________________ 10
2.2.4 Analog (Sensor) Base (ASB) ____________________ 10
2.2.5 Conventional detector __________________________ 10
2.2.6 (Conventional Detector) Base (CDB) ______________ 10
2.2.7 Addressable __________________________________ 10
2.2.8 Conventional zone line input / External line _________ 11
2.3 Output unit ______________________________________ 11
2.4 Output / Control output _____________________________ 11
2.5 Short circuit isolator (ISO) __________________________ 11
2.6 Display unit (D.U.) ________________________________ 11
2.7 COM loop _______________________________________ 11
2.8 Control Unit / C.U. / C.I.E. __________________________ 11
2.9 Fire Brigade Panel (FBP) ___________________________ 11
2.10 Control panel (CP) ________________________________ 11
2.11 System __________________________________________ 11
2.12 Network / TLON® / LonWorks® / Echelon / Node / TLON
Conn. board / Channel / Backbone net / Router / Repeater _______ 12
2.13 LED ____________________________________________ 12
2.14 External Indicator (Ext. LED) ________________________ 12
2.15 Display / LCD ____________________________________ 12
2.16 Door open (Door / Key switch) _______________________ 12
2.17 Site Specific Data (SSD) ____________________________ 13
2.18 Software (S/W) / System program ____________________ 13
3 Overview _________________________________ 14
3.1 The EBL512 G3 system ____________________________ 14
3.1.1 Printer ______________________________________ 14
3.1.2 Expansion boards _____________________________ 14
3.1.3 Power supply _________________________________ 14
3.2 S/W versions _____________________________________ 15
3.3 Documents ______________________________________ 15
3.4 Applications _____________________________________ 15
3.5 PC software (S/W) ________________________________ 15
3.5.1 WinG3 ______________________________________ 15
3.5.2 TLON Manager _______________________________ 16
3.5.3 WebG3 IConfig tool ___________________________ 16
4 Control Unit / TLON Network _______________ 17
1
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
4.1 The TLON network ________________________________ 17
4.2 Single TLON Network / redundant TLON Network ______ 17
5 Control Units 5000 and 5001 _________________ 19
5.1 Mounting plates ___________________________________ 21
5.1.1 Mounting plate for 19" mounting rack, 5020 ________ 21
5.1.2 Mounting plate for inflammable wall, 5021 _________ 21
5.2 COM loops ______________________________________ 22
5.3 Programmable voltage outputs (S0-S3) ________________ 24
5.4 Programmable relay outputs (R0-R1) __________________ 24
5.5 Programmable inputs (I0-I3) _________________________ 24
5.6 Relay outputs for routing equipment (tx) _______________ 25
5.6.1 Fire alarm output ______________________________ 25
5.6.2 Fault condition output __________________________ 25
6 Expansion boards 458x _____________________ 26
6.1 Expansion board no. (address) setting __________________ 27
6.2 8 zones expansion board 4580 _______________________ 27
6.2.1 Type of zone line input _________________________ 28
6.2.2 Input states __________________________________ 28
6.3 8 relays expansion board 4581 _______________________ 29
6.4 Inputs and outputs expansion board 4583 _______________ 30
6.5 I/O Matrix board 4582 _____________________________ 31
6.5.1 Generic _____________________________________ 33
6.5.2 Fan control __________________________________ 33
6.5.3 Zone control _________________________________ 34
7 Printer ___________________________________ 35
8 TLON connection board 1590 ________________ 36
8.1 Single TLON Network _____________________________ 36
8.2 Redundant TLON network __________________________ 36
8.3 Network programming _____________________________ 36
9 Peripheral devices __________________________ 37
9.1 COM loop units ___________________________________ 37
9.1.1 Input units ___________________________________ 39
9.1.2 Addressable I/O units __________________________ 46
9.1.3 Alarm devices (addressable sounders) _____________ 48
9.1.4 Short circuit isolators (addressable) _______________ 49
9.1.5 Units for Hazardous (Ex) areas ___________________ 50
9.1.6 Other COM loop units __________________________ 51
9.1.7 COM loop addresses for Base station and Wireless
detectors 54
9.2 Units connected to the RS485 interface ________________ 54
9.2.1 External Fire Brigade Panels _____________________ 55
9.2.2 Alert Annunciation Units _______________________ 56
9.2.3 External Presentation Units ______________________ 57
9.2.4 German Fire Brigade Panels _____________________ 58
9.3 Units connected to the RS232 interface J7 ______________ 59
2
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
9.3.1 Web-servers __________________________________ 59
9.4 Other units _______________________________________ 59
9.4.1 Alert Annunciation Controllers ___________________ 59
9.4.2 External LED ________________________________ 60
9.4.3 Alarm devices (sounders, etc.) ___________________ 60
9.4.4 Door release magnets __________________________ 60
9.4.5 Boxes _______________________________________ 61
9.4.6 Duct detector chambers _________________________ 61
10 Programmable inputs _______________________ 62
10.1 Control unit Inputs I0 - I3 & Inputs 0 -4 on exp. board 4583 63
10.1.1 Not supervised ________________________________ 63
10.1.2 Supervised ___________________________________ 63
10.2 The 3361 unit's Inputs In0 / Z & In1 ___________________ 63
11 Input programming ________________________ 64
11.1 Trigger conditions _________________________________ 64
11.2 Logic ___________________________________________ 67
11.2.1 Supervised ___________________________________ 67
12 Programmable outputs ______________________ 68
12.1 Control unit outputs S0 – S3 _________________________ 69
12.2 Control unit outputs R0 & R1 ________________________ 70
12.3 8 relays expansion board 4581 Output 0 – Output 7 _______ 70
12.4 Inputs and Outputs expansion board 4583 Output 0 & Output 170
12.5 The 3361 unit's Outputs Re0 & Re1 ___________________ 70
12.6 The 3364 unit's VO0 – VO2 _________________________ 71
12.7 The 3377 unit's Output (siren) ________________________ 71
12.8 The 3379 unit's Output (sounder) _____________________ 71
12.9 The 4380 unit's Output (beacon) ______________________ 71
13 Output programming _______________________ 72
13.1 Type of output ____________________________________ 72
13.2 Logic ___________________________________________ 73
13.3 Supervised / Not supervised _________________________ 73
13.4 Output signal period _______________________________ 73
13.5 Control expression ________________________________ 76
13.5.1 Trigger conditions _____________________________ 76
13.5.2 Logical operators ______________________________ 80
13.5.3 Control expression examples ____________________ 80
14 Interlocking function _______________________ 84
14.1 Programming of interlocking function _________________ 84
14.1.1 Interlocking output ____________________________ 84
14.1.2 Interlocking input _____________________________ 84
14.1.3 Interlocking combination _______________________ 84
14.2 Interlocking indications _____________________________ 86
14.3 Information of interlocking combinations (H9) __________ 86
14.3.1 Display interlocking information (H9/C1) __________ 86
14.3.2 Activate interlocking output (H9/C2) ______________ 87
3
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
14.3.3 Reset interlocking output (H9/C3) ________________ 87
14.3.4 Disable interlocking output (H9/C4) _______________ 87
14.3.5 Re-enable interlocking output (H9/C5) _____________ 87
14.4 Interlocking control expressions ______________________ 87
15 Fire Door Closing __________________________ 88
16 Functions / Services / Features _______________ 89
16.1 Sensor value _____________________________________ 89
16.2 Week average sensor value __________________________ 89
16.3 Decision value ____________________________________ 90
16.4 Alarm algorithms for smoke detectors / Detection levels /
Offsets 90
16.4.1 Alarm algorithm / Alternative alarm algorithm ______ 91
16.4.2 Filtering algorithm ____________________________ 92
16.4.3 Smouldering smoke algorithm ___________________ 94
16.5 Performance factor ________________________________ 95
16.6 Algorithms for analog heat detectors __________________ 96
16.6.1 Class A1 algorithm ____________________________ 97
16.6.2 Class A2 S algorithm __________________________ 97
16.6.3 Class B S algorithm ____________________________ 97
16.7 Self verification ___________________________________ 98
16.8 Minimum / Maximum sensor values ___________________ 98
16.9 2-zone / 2-address dependence (Co-incidence alarm) ______ 99
16.9.1 2-zone dependence ____________________________ 99
16.9.2 2-address (-unit) dependence ___________________ 100
16.9.3 Reset of 2-zone / 2-address dependence (co-incidence
alarm 100
16.10 Delayed alarm _________________________________ 101
16.11 Alert Annunciation _____________________________ 102
16.12 Alarm Acknowledgement Facility (AAF) ____________ 104
16.13 Quiet alarm ___________________________________ 106
16.14 Fire alarm type A and Fire alarm type B _____________ 106
16.14.1 Fire alarm type B ___________________________ 107
16.14.2 Fire alarm type A __________________________ 107
16.15 Disable alarm points and outputs __________________ 107
16.15.1 Disable zone ______________________________ 108
16.15.2 Disable zone / address _______________________ 108
16.15.3 Disable control output _______________________ 108
16.15.4 Disable / Re-enable output type _______________ 108
16.15.5 Disable / Re-enable alarm devices _____________ 108
16.16 Disable interlocking output _______________________ 108
16.17 Disable outputs for routing equipment ______________ 108
16.18 Disconnect & Re-connect loop / zone line input _______ 109
16.19 External time channels 15-63 _____________________ 109
16.20 Test mode ____________________________________ 109
16.21 Test alarm devices ______________________________ 109
4
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
16.22 Test of routing equipment ________________________ 110
16.23 Calibration of supervised outputs __________________ 110
16.24 Service signal _________________________________ 110
16.25 Fault signal (fault condition) ______________________ 111
16.26 Alarm texts ___________________________________ 111
16.26.1 Creating the alarm texts via WinG3 ____________ 111
16.26.2 Downloading alarm texts to the DU:s 1728 / 1735 /
1736 and ext. FBP:s 1826 / 1828 ________________________ 113
16.27 Real time clock (RTC) __________________________ 113
16.27.1 Daylight saving time ________________________ 114
16.28 Loss of main power source _______________________ 114
16.29 Evacuate _____________________________________ 114
16.30 WinG3 menu Tools _____________________________ 115
17 Special New Zealand functions ______________ 117
17.1 Alarm devices ___________________________________ 117
17.1.1 Silence alarm devices (inside switch) _____________ 117
17.1.2 New Zealand FB Silence switch (outside switch) ____ 117
17.2 Battery faults ____________________________________ 119
17.2.1 FAULT: Battery _____________________________ 119
17.2.2 FAULT: Low battery capacity __________________ 119
17.3 Watchdog reset __________________________________ 119
17.4 Routing equipment isolate (disable) __________________ 119
17.5 Acknowledged alarm _____________________________ 119
18 Cyber sensor functions _____________________ 121
18.1 Pulse up – down counter ___________________________ 122
18.1.1 Pulse up – down counter for smoke ______________ 122
18.1.2 Pulse up – down counter for temperature __________ 122
18.1.3 Pulse up – down counter for smoke & temperature __ 122
18.2 Fire judgement __________________________________ 122
18.3 Alarm threshold levels ____________________________ 123
18.4 Learning function / Learning conditions _______________ 123
18.4.1 Learning conditions ___________________________ 123
18.5 Alarm delay time _________________________________ 125
18.6 Analog data output _______________________________ 126
18.7 Sensitivity compensation __________________________ 126
18.8 Self diagnosis of internal devices ____________________ 127
18.9 Address setting check _____________________________ 127
19 Control unit properties ____________________ 128
19.1 Control unit properties dialog box ___________________ 128
19.1.1 General Information __________________________ 128
19.1.2 Peripherals __________________________________ 128
19.1.3 Misc. ______________________________________ 128
19.2 WinG3 Control unit pop-up menu ___________________ 129
19.2.1 Reset alarm counter ___________________________ 129
19.2.2 Software version _____________________________ 129
5
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
19.2.3 Upgrade number of alarm points _________________ 129
19.2.4 Restart _____________________________________ 130
19.2.5 Delete _____________________________________ 130
19.2.6 Properties___________________________________ 130
20 System properties (settings) _________________ 131
20.1 System properties dialog box _______________________ 131
20.1.1 Name ______________________________________ 131
20.1.2 User definable text ___________________________ 131
20.1.3 System properties, Page 1 ______________________ 131
20.1.4 System properties, Page 2 ______________________ 133
20.2 Menu System ____________________________________ 134
20.2.1 Properties___________________________________ 134
20.2.2 Time channels _______________________________ 134
20.2.3 Alarm algorithms ____________________________ 136
20.2.4 Output Signal Periods _________________________ 138
20.2.5 National holidays ____________________________ 139
20.2.6 Two zone dependence _________________________ 140
20.2.7 Statistics (System information) __________________ 141
20.2.8 Edit Alarm texts _____________________________ 141
21 Compatibility_____________________________ 142
22 Cable types ______________________________ 143
22.1 TLON Network cables ____________________________ 143
22.2 COM loop cables_________________________________ 143
22.3 Ext. FBP / Display Units cables _____________________ 143
22.4 Conventional zone line cables _______________________ 143
22.5 Alarm device cables ______________________________ 144
22.6 Other cables _____________________________________ 144
23 COM loop cable length _____________________ 145
24 Current consumption ______________________ 148
25 Power supply _____________________________ 152
25.1 Charger functions ________________________________ 153
25.1.1 Charging ___________________________________ 153
25.1.2 Battery charging functions: _____________________ 153
25.1.3 Security functions ____________________________ 153
25.2 Current consumption calculations ____________________ 154
25.3 Rectifier (main power source) _______________________ 155
25.4 Battery (second power source) ______________________ 155
25.5 Fuses __________________________________________ 156
25.6 Form / Table of current consumption _________________ 156
26 S/W versions _____________________________ 158
27 Technical data ____________________________ 159
28 Limitations_______________________________ 160
28.1 User definable texts _______________________________ 160
6
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
28.2 C.i.e. / System ___________________________________ 160
29 National regulations _______________________ 162
30 Drawings / connection diagrams _____________ 163
31 Revision history ___________________________ 164

Drawings according to the valid table of drawings.

7
Panasonic Electric Works Nordic AB
MEW01351 Rev: - Planning Instructions Fire alarm system EBL512 G3, V1.1.x
1 Introduction
EBL512 G3 Planning Instructions is a document1 intended to be used
by planning engineers as well as service / commissioning engineers.
This document should be read in conjunction with the drawings
according to the valid Table of drawings and the EBL512 G3
Operating Instructions MEW01163.
When planning a fire alarm installation the national regulations have
to be obeyed. A lot of detector types can be used. Detector coverage
area and detector placing in the room / building, etc. are matters for
the planning engineers and are not described in this document.
Due to continual development and improvement, different S/W
versions might be found. This document is valid for S/W version
1.1.x. On the date / revision date of the document x = 0.
Since the EBL512 G3 control unit (c.i.e.) is produced for many
countries the look, the texts, the functions, etc. might vary.
Products
Consists of one or more parts (HW) according to a Product Parts
List. A product has:
 a type number
5000 EBL512 G3 c.i.e. Configured for 128, 256 or 512 alarm
points and with or without printer depending on article number.
5001 EBL512 G3 c.i.e. No front panel and no Plexiglas in the
door. Configured for 128, 256 or 512 alarm points depending
on the article number.
 an article number is often the same as the type no. but a country
code can be added (e.g. SE for Sweden). If the letters PRT also
are added in the article number the product comes with a printer.
If digits are added to the article number they are showing the
number of alarm points configured (e.g. 5000PRTSE-128).
 a product name (e.g. EBL512 G3 CU, 128 alarm points, with
printer)
HW
A HW (e.g. a printed circuit board) has:
 a type number (e.g. 5010)
 an article number, often the same as the type no. but sometimes a
country code is added (e.g. 5010SE)

1 File name: L:\Retailers\Panasonic Russia\Training 110223_25\EBL512
G3\Documents\MEW01351(Rev -).doc
8