Mitsubishi M800/M80 CNC Alarm/Parameter Manual

606 Pages·2015·3.46 MB·English

Introduction
This manual is a guide for using the MITSUBISHI CNC M800/M80 Series.
This manual is prepared on the assumption that your machine is provided with all of M800/M80 Series functions. Confirm the
functions available for your NC before proceeding to operation by referring to the specification issued by the machine manu-
facturer.
Notes on Reading This Manual
(1) This manual explains general parameters as viewed from the NC.
For information about each machine tool, refer to manuals issued from the machine manufacturer.
If the descriptions relating to "restrictions" and "allowable conditions" conflict between this manual and the machine manu-
facturer's instruction manual, the later has priority over the former.
(2) This manual is intended to contain as much descriptions as possible even about special operations.
The operations to which no reference is made in this manual should be considered impossible.
CAUTION
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine tool
builder takes precedence over this manual.
Items not described in this manual must be interpreted as "not possible".
This manual is written on the assumption that all option functions are added.
Refer to the specifications issued by the machine tool builder before starting use.
Refer to the Instruction Manual issued by each machine tool builder for details on each machine tool.
Some screens and functions may differ depending on the NC system (or its version), and some functions may not be pos-
sible. Please confirm the specifications before use.

Precautions for Safety
Always read the specifications issued by the machine tool builder, this manual, related manuals and attached documents be-
fore installation, operation, programming, maintenance or inspection to ensure correct use.
Understand this numerical controller, safety items and cautions before using the unit.
This manual ranks the safety precautions into "DANGER", "WARNING" and "CAUTION".
DANGER
When the user may be subject to imminent fatalities or major injuries if handling is mistaken.
WARNING
When the user may be subject to fatalities or major injuries if handling is mistaken.
CAUTION
When the user may be subject to injuries or when physical damage may occur if handling is mistaken.
Note that even items ranked as " CAUTION", may lead to major results depending on the situation. In any case, important in-
formation that must always be observed is described.
The following sings indicate prohibition and compulsory.
This sign indicates prohibited behavior (must not do).
For example, indicates "Keep fire away".
This sign indicated a thing that is pompously (must do).
For example, indicates "it must be grounded".
The meaning of each pictorial sing is as follows.

CAUTION CAUTION CAUTION HOT Danger Danger
rotated object Electric shock risk explosive

Prohibited Disassembly is KEEP FIRE AWAY General instruction Earth ground
prohibited
For Safe Use
Mitsubishi CNC is designed and manufactured solely for applications to machine tools to be used for industrial purposes.
Do not use this product in any applications other than those specified above, especially those which are substantially influential
on the public interest or which are expected to have significant influence on human lives or properties.
DANGER
Not applicable in this manual.
WARNING
Not applicable in this manual.
CAUTION
(1) Product and manual
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine tool
builder takes precedence over this manual.
Items not described in this manual must be interpreted as "not possible".
This manual is written on the assumption that all option functions are added. Refer to the specifications issued by the ma-
chine tool builder before starting use.
Refer to the Instruction Manual issued by each machine tool builder for details on each machine tool.
Some screens and functions may differ depending on the NC system (or its version), and some functions may not be pos-
sible. Please confirm the specifications before use.
(2) Adjustments
Do not adjust or change the parameter settings greatly as operation could become unstable.
In the explanation on bits, set all bits not used, including blank bits, to "0".
(3) Troubleshooting
If the battery low warning is issued in the controller side, save the machining programs, tool data and parameters in an
input/output device, and then replace the battery. When the battery alarm is issued, the machining programs, tool data and
parameters may have been destroyed. Replace the battery and then reload the data.
If the battery low warning is issued in the drive unit side, immediately replace the battery. Replace the batteries while ap-
plying the drive unit's control power.
(4) Maintenance, inspection and part replacement
Do not short-circuit, charge, heat, incinerate or disassemble the battery.
Dispose of the spent battery according to local laws.
Disposal
(Note) This symbol mark is for EU countries only.
This symbol mark is according to the directive 2006/66/EC Article 20 Information for end-
users and Annex II.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and
components which can be recycled and/or reused.
This symbol means that batteries and accumulators, at their end-of-life, should be disposed of
separately from your household waste.
If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means that the
battery or accumulator contains a heavy metal at a certain concentration. This will be indicated as
follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used batteries and accumulators.
Please, dispose of batteries and accumulators correctly at your local community waste collection/
recycling centre.
Please, help us to conserve the environment we live in!

Trademarks

MELDAS, MELSEC, EZSocket, EZMotion, iQ Platform, MELSOFT, GOT, CC-Link, CC-Link/LT and CC-Link
IE are either trademarks or registered trademarks of Mitsubishi Electric Corporation in Japan and/or other
countries.

Ethernet is a registered trademark of Xerox Corporation in the United States and/or other countries.
Microsoft® and Windows® are either trademarks or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
SD logo and SDHC logo are either registered trademarks or trademarks of LLC.
UNIX is a registered trademark of The Open Group in the United States and/or other countries.
Intel® and Pentium® are either trademarks or registered trademarks of Intel Corporation in the United States
and/or other countries.
MODBUS® is either trademark or registered trademark of Schneider Electric USA, Inc. or the affiliated
companies in Japan and/or other countries.

Other company and product names that appear in this manual are trademarks or registered trademarks of the
respective companies.

本製品の取扱いについて
(日本語/Japanese)
本製品は工業用(クラスA)電磁環境適合機器です。販売者あるいは使用者はこの点に注意し、住商業環境以外で
の使用をお願いいたします。
Handling of our product
(English)
This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
본 제품의 취급에 대해서
(한국어/Korean)
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며 가정외의 지역에
서 사용하는 것을 목적으로 합니다.