GlobalGuard Alarm System HISK1 - Friedland

78 Pages·2012·2.79 MB·English

GlobalGuard Alarm System
HISK1

Hardware Installation and Operating Manual

1
FOREWORD
All devices in this wireless Alarm System are
Tools and Equipment Required:
designed and manufactured to provide long
reliable service. The system is designed for No.0 Philips Screwdrivers
ease of installation using only conventional Bradawl
No.1 Philips Screwdrivers
domestic tools. However, it is essential that the
Drill
installer reads and fully understands the advice
No.2 Philips Screwdrivers
and procedures contained in this manual and
3mm Drill Bit
plans the system before proceeding with the Small Spirit Level
installation. 5 & 6mm Masonry Drill Bits

DEVICE RANGE
IMPORTANT:
The quoted range of the system devices (see
component specification on rear cover) is
LOCAL AUTHORITY REGULATIONS
measured in ideal conditions. Any solid object
AND LEGISLATION'
(e.g. walls, ceilings, reinforced PVC doors etc)
placed between the transmitter and Receiver
This alarm system should be installed and
device will reduce the radio range.
operated in accordance with the requirements of
any current local and/or national regulations and
The amount by which the range will be reduced
legislation. We recommend that you contact
is dependent upon the nature of the barrier. For
your authority to obtain details of your area's
example:
requirements local and/or national regulations.
Wall Type Range
For example in Belgium, the installation and use
Reduction
of an alarm system including notification by
telephone (Voice Dialler) functionality and the
Dry-lined partition wall: 10-30%
optional use of an external siren is controlled by Single layer brick wall: 20-40%
Belgium legislation "KB" of 19/06/2002. Double layer brick wall: 30-70%
Metal panel/radiator: 90-100%

Note: The effect on the range of multiple walls is
DECLARATION cumulative. i.e. if there are 2 brick walls in the
way, the range will be reduced by up to 40% by
Novar ED&S hereby declares that this wireless
each wall.
alarm system is in compliance with the essential
requirements and other relevant provisions of
the Radio and Telecommunications Terminal
Equipment (R&TTE) directive, 1999/5/EC. SYSTEM SECURITY
This system has been designed to both detect

intruders and act as a strong deterrent to would-

be intruders when installed correctly.

Please remember that given adequate
knowledge and time it is possible to overcome
any alarm system and we therefore recommend

that your Alarm is used in conjunction with good
2
physical protection such as security window and - An unrestricted internet broadband
door locks. connection with wired or wireless (Wifi)
connectivity. (For optional wireless
All units in the system are encoded to operate indoor CCTV accessory, Wifi will allow
together using an 20 bit rolling House Code. you connect the camera to the router
The system House Code is automatically wirelessly)
changed each time the system is
- A PC with;
armed/disarmed or triggered by a detector.
• Operating System:
The system can be operated from one or more
Windows XP/Vista/Window7
accessory Remote Control Units and/or
Keypads. It can also be operated remotely over • Internet Explorer 6.x or higher Internet
the internet using a PC or mobile Web Browser
device(Android/Apple IOS device). Care should • CPU: Pentium 4, 1GHz or above
be taken to ensure that any of your Remote
• VGA Card Resolution: 800x600 or
Control Units are not lost or the User Access
above
PIN Code for the Control Panel do not become
known to other people as this will compromise • Video Memory Size: 128Mb or above
the security of your system. The User Access • Recommended internet upload speed
PIN Code should be changed as soon as 512kbp/s for 1 x IP Camera (optional)
possible.
or 2Mbp/s for 8 x cameras connected

Optional Android or Apple IOS
HOME AUTOMATION CONTROL Smartphone/mobile device;

The system allows you to create Programmes,
• IOS: iPhone1/2/3/4, iPad1/2, iPod
Schedules and Events using the GlobalGuard
Touch 4 up to IOS V4.3. 4(latest iOS
PC setup software. Home automation allows you Version release)
to control wireless ON/OFF switching devices • Android: Android phone V2.X, tablet PC
together with security arming. There are 3 tested up to V4.0
function keys I/II/III located on the side of the
Control Panel which are programmable via the
PC software and each function key can store a
Programme. The activation of a Programme can PROGRAMMING THE SYSTEM
be instantly activated simply by pressing one of
the corresponding function keys. The system can be setup using the instructions
in this manual or alternatively using the

GlobalGuard PC setup software available at
REMOTE ACCESS AND SYSTEM www.GlobalGuard.Friedland.co.uk

REQUIREMENTS
Note that home automation Programmes,

Events and Schedules can only programmed
This system is supplied pre-linked to an IP using the PC software. This means that the
gateway module which allows you to remotely function keys I/II/III located on the side of the
access and control your system via the internet.
Control Panel can only be programmed from the
In order to get the full benefits of the system,
PC software.
please ensure you meet the following

requirements:
If using a PC to run the setup software then
• A broadband router with x2 spare LAN ports
ensure that it is connected wired or
(x1 for IP gateway and other for an optional IP
wirelessly (WIFI) to the same internet
Camera if added in future)
broadband router as that connected to the IP
3
Gateway otherwise the software will not run
correctly. If using a WIFI connection, ensure
the PC is within operating range of the router.

SECURITY DEVICES BACKWARD
COMPATIBILITY

Please note that earlier versions of the
Response branded 868MHz security PIR
movement detectors, magnetic door/window
contact detectors, remote control and remote
keypad devices are also compatible with this

system.
If you are upgrading an existing Response

868MHz wireless security system you already
purchased in the past, then you can reuse the
existing security devices installed by simply
linking one each to the GlobalGuard system.

SAFETY

Always follow the manufacturer’s advice when
using power tools; steps, ladders etc. and wear
suitable protective equipment (e.g. safety

goggles) when drilling holes etc.
Before drilling holes in walls, check for hidden

electricity cables and water pipes, the use of a
cable/pipe locater maybe advisable if in doubt.

When using ladders, ensure that they are
positioned on a firm stable surface at the correct
angle and suitably secured before use.
The use of ear defenders is advisable when
working in close proximity to the Siren due to the
high sound level produced by this device.

4
CONTENTS PASSIVE INFRA-RED (PIR) MOVEMENT

DETECTOR 20
KIT CONTENTS 7 Positioning the PIR Detectors 21
Installing the PIR Movement
INTRODUCTION AND OVERVIEW 8
Detector 21
Multiple Users 8 Testing the PIR Detector Independently 22
User Access PIN Code 8 Linking A PIR Detector To The Control
System Arming 8 Panel 23
Entry/Exit Delay 8 Testing the PIR Detector with the
Zones 9 Control Panel 24
Zone Lockout 9
Quick Set 9
MAGNETIC CONTACT DETECTORS 25
Event Log 9
Positioning the Magnetic Contact
Chime 10
Detectors 25
Tamper Protection 10
Installing and Configuring the
Jamming Detection 10
Magnetic Contact Detectors 25
Battery Monitoring 10
Testing A Magnetic Contact Detector
Home Automation 10
Independently 27

Linking A Magnetic Contact Detector
PLANNING AND EXTENDING 11
To The Control Panel 27
YOUR ALARM SYSTEM Testing the Magnetic Contact

Detector with the Control Panel 28
EXTERNAL SOLAR SIREN 14

Configuring the Solar Siren 14
INSTALLING THE SOLAR SIREN AFTER
Charging the Solar Siren Battery 15
CHARGING 29

Testing the Siren from the Control
CONTROL PANEL 16
Panel 30
Positioning the Control Panel 16
Mounting the Siren on the wall 31
Control Panel Overview 16

Installing the Control Panel 17

REMOTE CONTROL UNIT (OPTIONAL
IP GATEWAY 18
ACCESSORY) 31
Installing the IP Gateway 19
Configuring the Remote Control 31
LED Indications 19
Testing the Remote Control 32
Linking An IP Gateway To The
Linking a Remote Control or
Control Panel(Optional) 19
Remote Keypad to the Control Panel 32
Deleting The IP Gateway From

The Control Panel(Optional) 20
EXTERNAL CONNECTIONS 35

TESTING THE SYSTEM 37
5
DEFAULT SETTINGS 39 Device Remote Access Control 59
Home Automation/Remote Sensor 60
RESET 41
Learning a transmitter 60

PROGRAMMING 42
Communication Device Setup 61

Learning/replacing a communication
User Setup 42
device 61
Learn Remote Control 44

Backup & Restore 62
System Setup 46
OPERATING INSTRUCTIONS
Internal Siren 47
Alarm Duration 47 Fully Arming The System 62
Wireless Siren 47 Holiday Arming The System 63
Night Alarm 47 Part-Arming The System: Part-Arm-I 64
Warning/Error Beep 48 Part-Arming The System: Part-Arm-II 64
Jamming Detection 48 Disarming the System 64
Alarm Relay 48 Disarming the System with
Zone Lockout 49 the Duress Code 64
Part-Arm I Setup 49 Spectra Lightening 64
Part-Arm II Setup 49 Quick Set 65
Fully Arm Setup 49 Home Automation Function
Holiday Arm Setup 50 Keys I/II/III 65
Date and Time Setup 50 Personal Attack (PA) Alarm 65
Learn Wireless Keypad 50 Zone Lockout 65
Link Panel To Friedland Device Tamper 66
Spectra Receiver (Optional) 52 Chime 66
Lighting Setup For Spectra Receiver 52 Keyboard Beep Mute 66
Entry/Exit Beeps 66
Security Detector/Zone Setup 53 Event Log 66
Learn Detector Code 53 Siren Service/Operating Mode 67
Chime 55 Battery Monitoring 68
Part-Arm I Setup For Zone Detector 55
MAINTENANCE 69
Part-Arm II Setup For Zone Detector 55
Detector Status 56
ALARM RECORD 71
Detector Remove 56
Siren At Trigger 56 USER PIN CODE NOTES 72
Entry Delay 56
TROUBLESHOOTING 73

Home Automation Setup 58
EXTENDING YOUR ALARM SYSTEM 75
Home Automation Control 59
Learning a receiver 59 COMPONENT SPECIFICATION 77
All Turn ON 59

6
Please visit www.GlobalGuard.Friedland.co.uk
KIT CONTENTS to view an online installation video. Further
details on setup and operation can be found in
The Alarm System should contain the following devices both this and the online software manual
1 x Solar Siren
1 x LCD Control Panel
1 x IP Gateway
1 x Wireless USB Dongle
1 x PIR Movement Detector
1 x Magnetic Door /Window Detector

Also included:
1 x 12VDC Power Supply Adaptor (For Control Panel
Solar Siren
and charging Siren)
1 x 5VDC Power Supply Adaptor

1 x 0.5m Ethernet cable
Siren Mounting Template
Quick Start Guide
Fixings Pack

Batteries
PIR Movement
Detector Door/W indow
Contact Dete ctor

2 x NiMH batteries (6V for Control Panel

and 7.2V for Siren)
Control Panel
Wireless IP
Gateway

3V CR2032 12V DC Power supply
9V PP3 Alkaline
Lithium Coin Cells adaptor
Battery (for PIR
(for Door/Window 5V DC Power supply adaptor
Movement
Detector)
Detector)

HEALTH WARNING: Ethernet cable
Do not put the coin cell batt ery in your mouth as this could impair
your health. Keep this cell out of reach from young children as
they could swallow it and choke.

7
INTRODUCTION AND left un-occupied, the ‘Fully Arm’ mode will arm
all zones to protect the entire property, (i.e.
OVERVIEW
upper and lower floors and outbuildings).

MULTIPLE USERS
The system allows for up to 8 Users, a Master
(Admin) and 7 Users to be configured. This
allows the system Event Log to maintain a
record of which users have armed and disarmed
the system. Each user will have a different User
Access PIN Code. Fully & Holiday Arm
Only the Admin User has access to the
programming functions and is able to configure
the system.

USER ACCESS PIN CODE
Part-Arm-I
The Control Panel is the brains of the system
and is where the system is programmed and
operated from. A 4 digit PIN code is used to
ensure that only authorized people have access
to the system. This is the User access PIN code
and can be set to a code of your choice that only
you and other authorized system users know.

Part-Arm-II

SYSTEM ARMING
ENTRY/EXIT DELAY
The system has a ‘Fully Arm’, two ‘Part-Arm’
and a ‘Holiday Arm’ modes. Fully Arm and
When the system is armed with the Exit-Delay
Holiday Arm will ‘Arm’ all zones while the ‘Part-
enabled, no signal from any detector on an
Arm’ modes will only arm the zones that are
active zone will be able to trigger an alarm until
enabled for the particular Part-Arm mode.
the Exit-Delay has expired. This enables the
system to be armed from within the property and
For example:
allows time for the user to exit the property
without triggering an alarm. If the Exit-Delay is
The system could be configured so that during
disabled then detectors on active zones will
night time, ‘Part-Arm-I’ would arm only zones
immediately be able to trigger an alarm once the
protecting the lower floor and outbuildings
system is armed.
leaving the upper floor free for movement
without triggering the alarm.
Zones1&2 only have been pre-configured
with an entry/exit delay of 30 seconds
During the day while the property is occupied
because detectors added on these zones are
‘Part-Arm-II’ could arm only the zones protecting
the outbuildings. However, when the property is
8
typically installed at entry/exit points of your – ‘24-hour Intruder’ mode provides 24 hour
property. intruder protection for areas where continuous
monitoring is required, (e.g. gun lockers).
The system Exit-Delay may be configured for
between 10 to 250 seconds or disabled – ‘Fire’ mode provides 24 hour monitoring of any
completely. Smoke detectors incorporated into the system.
If a detector on a zone with its Entry-Delay – ‘Test’ mode allows a zone to be monitored
enabled is triggered, then an alarm will not while the system is armed. If a detector on a
sound until the Entry-Delay period has expired. zone is triggered an entry will be recorded in the
This allows time for the user to re-enter the Event Log but an alarm will not occur.
property and disarm the system before an alarm
In addition there is the facility to connect up to 4
occurs. Generally only the zones on the main
hard wired zones to the Control Panel, each of
entry route to the property will be configured with
which is configurable with most of the features of
an Entry-Delay. The remaining zones would be
the wireless zones.
configured with their Entry-Delay disabled
allowing them to immediately initiate an alarm

the instant a detector on the zone is triggered.
ZONE LOCKOUT
The Entry-Delay for each zone may be
configured for between 10 to 250 seconds or
If a detector on an active zone is triggered while
disabled completely.
the system is armed an alarm will sound. After
the programmed alarm duration has expired the
Note: To conserve power and maximize battery
alarm will stop and the system will automatically
life the PIR movement Detector will only detect
reset.
movement if there has been no movement
detected within the previous 2 minutes.
Subsequent detectors triggered will again trigger
Consequently the PIR Detector will not become
an alarm. If a single zone triggers an alarm more
active until the protected area has been free
than 3 times then that zone will be ‘Locked Out’
from movement for more than 3 minutes.
and any further alarm signals from that zone will
be ignored until the system is disarmed.

Note: The ‘Zone Lockout’ feature can be
ZONES
disabled if required.
The system incorporates 32 wireless alarm

zones for the connection of a PIR movement or
door/window contact detector per zone used to
QUICK SET
independently monitor different areas of the
property. In addition to standard intruder The system may be fully armed in 10 seconds
protection, each zone can also be configured to
using the quick set facility, overriding the
operate in alternative modes.
programmed exit-delay. This is useful for setting
the system at night when the Exit-Delay warning

beep will be silenced after just a few seconds.
For example:

– ‘Intruder’ mode provides standard intruder
EVENT LOG
monitoring.
The Control Panel incorporates a memory
capable of storing the last 99 system events.
9
This enables the user to see which user has The jamming detection circuit will constantly
Armed/Disarmed the system and if and when scan for jamming signals. However, it will also
any alarms occurred. The time, date and details detect and could in extreme cases be triggered
of the event type will be recorded for each by radio signals from other radio equipment
system event. within range operating on the same frequency
which would not interfere with the normal
CHIME operation of your alarm.
Chime is a low security facility for use when the If you are planning to operate the Jamming
system is in Standby mode. If the Chime feature Detection feature we recommend that you wait
is ON, and a detector on a zone that has its at least 30 days before activating this feature to
Chime function enabled is triggered, the internal allow time for you to become familiar with the
sounder will produce a low volume warning tone. operation of your system.
A typical use of the Chime function would be to
warn that a door or particular area has been
entered.
When activating jamming detection the system
should be monitored carefully for false jamming
alarms for at least 2 weeks before leaving the
TAMPER PROTECTION
Jamming Detection function permanently
enabled.
All security related system devices (except any
Remote Control Units) incorporate Tamper
protection features to protect against
unauthorized attempts to interfere with the BATTERY MONITORING
device.
All security devices powered by non-
Any attempt to remove the battery cover from rechargeable batteries incorporate a battery
any device (except a Remote Control) or to level monitoring feature which will warn of a low
remove the Solar Siren or Control Panel from battery status.
the wall will trigger the alarm even if the system
is Disarmed (unless the system is in Test or In addition the Control Panel will also indicate a
Program modes). low battery status on any PIR (Passive Infra-
Red) movement or Magnetic Door /Window
Detector on the system.
JAMMING DETECTION The batteries on any device indicating a low
battery status should be replaced immediately.
In order to detect any attempts to illegally jam
the radio channel used by your alarm system, a
special jamming detection function is
incorporated into the Control Panel. If this HOME AUTOMATION
feature is enabled, an alarm will be triggered if
This system can also accommodate up to 32
the radio channel is jammed continuously for
wireless receiver home automation devices.
more than 30 seconds or if the system is
Devices include an ON/OFF Plugin Controller or
jammed for more than 3 periods of 10 seconds
Bayonet Lampholder.
in a 5 minute period. At full alarm it will beep for
3 seconds and will alarm after 10 seconds. At
These devices are used to simulate the
Part Arm it will beep for 3 seconds.
presence of occupants whilst you are away from
the home.
10