Apex R8 Owner's Manual - Diamondback Fitness

32 Pages·2009·2.2 MB·English

Diamondback Fitness • 6004 S. 190th Street, Suite 101 • Kent, WA 98032 • Ph: 800.776.7642
DP #: 22-10-1038 © Diamondback Fitness 2009
PM4197
Apex R8 Owner’s Manual
PURCHASER’S REFERENCE INFORMATION
Product Name Diamondback Fitness Apex R8 Upright
Serial Number: E _ _ _ _ _ _ _ _ _ _
Record the serial number here.
Serial Number Location
The serial number will be located on the right side of the lower main S|E|||R|||I A|||L| ||N|||U| |M||P||B|||E|||RL E
frame, just forward of the rear stabilizer (see figure to the right). WSARNAIEN0G0:M0 R00E0M0O00VAL OR
DESTRUCTION OF THIS
LABEL VOIDS WARRANTY
Record of Purchase
NOTE: Please record details associated with the purchase of your Diamondback Fitness Apex R8 below. This
information will be required in the event the unit requires future service. ATTACH THE PURCHASE RECEIPT.
Dealer Name: ___________________________________________ Dealer Telephone Number: ( ) _____________________________
Dealer Address: _________________________________________________________________________________________________________
Date Purchased: ________________________________________ Dealer Contact Name: ________________________________________
To Activate Your Warranty
Please register the unit at www.diamondbackfitness.com. Failure to comply may limit or void your warranty coverage.
2
Diamondback Fitness
Apex R8
Owner’s Manual
Release v.2 (11/2009) 3
TABLE OF CONTENTS
PURCHASER’S REFERENCE INFORMATION.................................................................... 2
Serial Number: ....................................................................................... 2
INTRODUCTION ..........................................................................................5
APEX R8 ASSEMBLY ......................................................................................6
Assembly Instructions .................................................................................7
SAFETY INSTRUCTIONS & WARNINGS ........................................................................8
WORKOUT GUIDELINES................................................................................... 12
Good Health is an Exercise in Common Sense ............................................................. 12
Body Mass Index .................................................................................... 12
Heart Rate is an Important Key to Your Exercise ............................................................ 13
Touch Heart Rate Sensors ............................................................................. 13
Wireless Heart Rate Receiver ........................................................................... 13
Your Estimated Maximum Heart Rate & Target Training Zone ................................................... 14
WORKOUT QUALITY AND QUANTITY ........................................................................15
CONSOLE LAYOUT....................................................................................... 17
Buttons And Keys ................................................................................... 19
Quick Keys ........................................................................................ 20
MP3/iPod Input Jack and Speakers ...................................................................... 20
PROGRAMS ............................................................................................21
Quick Start ........................................................................................ 21
User Select Mode and User Set-Up Mode ................................................................. 21
Program Select Mode ................................................................................ 22
Manual Program .................................................................................... 22
Target Heart Rate ................................................................................... 23
Classic Programs .................................................................................... 24
User Program ...................................................................................... 25
Watt Program ...................................................................................... 25
MAINTENANCE.......................................................................................... 26
WARRANTY INFORMATION ................................................................................27
WARRANTY REGISTRATION CARD ..........................................................................30
4
INTRODUCTION
Congratulations on the purchase of your new Diamondback Fitness Apex R8 Exercise Bicycle. You have made a smart choice
and are about to enjoy one of the most effective and technically-advanced methods of cardiovascular exercise available today.
Founded in 1991 as an off-shoot of the legendary bicycle company, Diamondback Fitness was in many ways a complimentary
addition to the Diamondback brand. One might even say this extension grew as a natural evolution…an evolution from classic
outdoor bicycle usage, toward indoor-based cycling and cross training. It turns out that many fitness enthusiasts were searching
for ways to maintain conditioning during times of inclement weather or were simply looking for new and different cross-training
options.
This trend still continues today, twenty years later, as the strong Diamondback brand resonates with both the boomers who
grew up with the bicycles, as well as the younger generations riding them today.
Diamondback Fitness continues to build upon this legendary brand identity by offering the cardio enthusiast a full line of
upright exercise bicycles, recumbents, and elliptical trainers, each offering superior value and quality in an intuitive and visually-
appealing design. Let’s just say, we are already planning our next twenty years.
Thank you for choosing Diamondback Fitness.
Diamondback Fitness
6004 South 190th Street, Suite 101 Kent WA 98032 Ph: 1.800.776.7642 Fax: [phone]
For more information or questions regarding your equipment, please visit our web site at DiamondbackFitness.com.
5
Part Description
APEX R8 ASSEMBLY A . . . . . . . . . .Front Stabilizer [Quantity 1]
B . . . . . . . . . .Rear Stabilizer [1]
C . . . . . . . . . .Hex Bolt - M8 x 1 .25 x 16 mm (6 mm socket) [4]
X D . . . . . . . . . .Leveling Foot / End Cap [2]
E1 . . . . . . . . .Pedal – Left [1]
E2 . . . . . . . . .Pedal – Right [1]
F1 . . . . . . . . .Flat Washer – 8 .0 x 19 .0 x 2 .0 mm [4]
W5 W4 W3 W2 F2 . . . . . . . . .Hex Bolt - M8 x 1 .25 x 16 mm [4]
W1 G . . . . . . . . . .Seatback Assembly [1]
Y H1 . . . . . . . . .Flat Washer – 8 .0 x 19 .0 x 2 .0 mm [4]
H2 . . . . . . . . .Hex Bolt - M8 x 1 .25 x 16 mm [4]
S2 Z J . . . . . . . . . .Handlebar Assembly - Rear [1]
V Q2 JJ K1 . . . . . . . . .Flat Washer – 8 .0 x 19 .0 x 2 .0 mm [4]
AA K2 . . . . . . . . .Hex Bolt – 8 x 1 .25 x 45 mm (6 mm socket) [4]
BB L . . . . . . . . . .Seat Base [1]
T CC
M . . . . . . . . . .Hex Screw – M5 x 0 .8 x 12 mm (3 mm socket) [2]
U3 N1 . . . . . . . . .Water Bottle Cage [1]
U2 N2 NP 2 . . . . . . . . . . . . . . . . . . .WHeaatertr RBaottet leW i[r1e] Harness – Lower; Connector 1 [1]
U1 N1 Q1 . . . . . . . . .Heart Rate Wire Harness – Upper; Connector 1 [1]
DD L Q2 . . . . . . . . .Heart Rate Wire Harness – Upper; Connector 2 [1]
FF Q1 R S1 EM2 RS1 . . . . . . . . . . . . . . . . . . .WWiirree HHaarrnneessss –– LUopwpeerr;; CCoonnnneeccttoorr 11 [[11]]
P S2 . . . . . . . . .Wire Harness – Upper; Connector 2 [1]
T . . . . . . . . . .Console Mast Assembly [1]
C HH G U1 . . . . . . . . .Hex Bolt - M8 x 1 .25 x 16 mm (6 mm socket) [5]
U2 . . . . . . . . .Flat Washer – 8 .0 x 19 .0 x 2 .0 mm [4]
A K1 U3 . . . . . . . . .Curved Washer – 8 .0 x 19 .0 x 2 .0 mm [1]
EE
K2 F1 F2 J VW .1 . . . . . . . . . . . . . . . . . .HHaannddlleebbaarr AFisxsinegm Cbllya m- pF r o[1nt] [1]
W2 . . . . . . . . .Flat Washer – 7 .0 x 12 .0 x 1 .0 mm [2]
W3 . . . . . . . . .Lock Washer – 7 .0 x 8 .0 x . 2 .0 mm [2]
H1 W4 . . . . . . . . .Hex Bolt – M7 x 1 .0 x 30 mm [2]
EE
W5 . . . . . . . . .Handlebar Clamp Cover [1]
H2 X . . . . . . . . . .Console [1]
E1 Y . . . . . . . . . .Wire Harness - Console [1]
Z . . . . . . . . . .Heart Rate Wire Harness - Console [1]
C GG AA . . . . . . . . .Phillips Screw – M5 x .8 x 10 mm [4]
BB . . . . . . . . .Console Tilt Hinge Cover [1]
CC . . . . . . . . .Phillip Wood Screw – M4 x 10 mm [2]
DD . . . . . . . . .AC Adaptor – US Plug; 120V, 60 Hz, 9V, 1A . [1]
EE . . . . . . . . .Crank Caps [2]
D FF . . . . . . . . .Console Mast Cover [1]
GG . . . . . . . . .Heart Rate Wire Pigtail [1]
B
6 HH . . . . . . . . .Input Jack [1]
JJ . . . . . . . . .Console Mounting Plate [1]
Assembly Instructions
1
E2
Apex R8 Assembly Hardware Kit
C
DP #22-10-1040 A HH
EE
Allen Bolt Bushing Allen Wrench (1)
M7 x 1.0 x 30 mm (1) ID 7.0 x OD 12.0 x 40 mm (1)
EE
FlIaDt 7 .W0 mams h(2)er LoIcD k7. 0W mams (2h)er Handlebar Clamp (1)
T-Handle M7 x 65 mm (1) E1 C

Pedal Wrench / Screwdriver (1)
Crank Bolt & Nut Wrench / Screwdriver D B
Notes:
Remove the hex fixing bolts (B) from the front stabilizer (A) and rear
• Please read the entire Apex R8 Owner’s stabilizer (C). Align the holes in the main frame with the recessed nuts in
Manual prior to beginning the assembly. the stabilizers and reinstall the fixing bolts.
• Review the package contents to ensure Level the base by adjusting the leveling feet integrated into each of the
all listed parts are included. rear stabilizer end caps (D). Rotate the knobs counter-clockwise to raise
• The assembly will require a 15 mm box the feet and clockwise to lower them.
wrench, a 6 mm hex wrench, a 15 mm Remove the left and right crank caps (EE), un-threading them counter-
pedal wrench, and a Phillips screwdriver. clockwise. Tighten both crank nuts (clockwise) with the enclosed box
All required tools are included. wrench and replace the crank caps.
• The estimated assembly time (of the Thread the left pedal (E1) into the left crank in a counter-clockwise
Apex R8) for a person familiar with basic direction. Tighten firmly with the spanner wrench.
tool usage is thirty (30) to forty-five (45)
Install the right pedal (E2) into the right crank, tightening in a clockwise
minutes. direction. Reinstall the crank caps (EE).
7
2 3
Remove the four (4) hex fixing bolts
W5 W4 W3 W2 W1
(F1) and flat washers (F2) from the T
seat slide assembly. Align holes in U3 N1
the seat back (G) mounting plate U2 M N2 L
with the holes in the seat slide and U1 R S1 V
reinstall the four (4) sets of F1 & F2. Q1
FF K1 G
Aunligdne rtshidee f ioxifn sge haot lbeass ien (tLh)e with P K2 KK G
GG
holes in the two square tubes F1 F2 J
welded to the seat slide assembly. H1
Install the four (4) sets of flat H2
washers (K1) and hex bolts (K2)
through the underside of the holes
in the square tubes and into the
seat base.
Remove the four (4) sets of flat washers
Remove the two (2) hex bolts (M) from the console mast (T). Align the two
(H1) and hex bolts (H2) from the rear
holes in the bottle cage (N1) with the holes in the console mast and tighten
mounting plate of the seat back (G). Align
with the Phillips screwdriver provided. Slide the bottle (N2) into the cage.
the mounting holes of the rear handlebar
Remove the five (5) hex bolts (U1), four (4) flat washers (U2) and one (1) (J) with the seat back mounting plate holes,
curved washer (U3) from the console mast (T) and set aside. and reinstall parts H1 & H2.
Slide the console mast cover (FF) onto the console mast. Plug the loose end of the heart rate wire
pigtail (GG) into the jack located in the
While supporting the console mast, join plugs (P) and (Q1) and (R) with (S1).
center of the fixing bolts on the rear
Slide the console mast (T) over the receiver on the main frame taking care not handlebar (J).
to pinch the wires as they are tucked into the frame. Re-install parts U1, U2 &
While supporting the front handlebar (V),
U3 only into the three lower holes and tighten.
install handlebar clamp assembly W1,
Slide the console mast cover (FF) downward and snap into place. W2, W3, W4 & W5 as per the diagram.
Determine the preferred angle of the bar
Re-install the two (2) bolts (U1) and washers (U2) into the upper holes and
prior to tightening the hardware completely.
tighten.
8
4 5
BB
X FINAL SETUP & INSTALLATION
CC
Move into Position. Move the unit into final position with the help
Y
JJ Z of the front transport rollers. Carefully lift and support the rear end
AA
of the unit until both transport wheels touch the ground. Slowly roll
HH into position unit into place.
Level the Frame for Stability. After moving the unit, ensure all
four feet touch the floor. Level the base by adjusting the leveling
KK feet which are integrated into each of the two rear stabilizer end
DD caps (D). Rotate the knobs counter-clockwise to raise the feet and
D clockwise to lower them.
Adjust the Seat. The seat slides fore and aft along a fixed rail. The
proper seat adjustment positions the user so their leg would be
slightly bent when the pedal is at the furthest position from the seat.
Remove the two (2) fixing screws (CC) from the To move the seat, loosen the seat adjustment knob (KK) a few
back side of the console hinge cover (BB) the four turns, rotating it counter-clockwise. Release any fore/aft pressure
(4) fixing screws (AA) from the console back (X). on the seat then pull the spring-loaded knob outward, away from
the frame to retract the positioning. Slide the seat forward or
While supporting the console (X), join the heart rate
backward along the track and release the knob, making sure the
wire connectors (Q2) and connector (Z) and wire
seat pin is engaged in a positioning hole by sliding the seat along
harness connector (S2) with connector (Y).
the track. An audible clunk may be heard as the pin enters the hole.
Align the fixing holes in the backside of the console
With the seat into position, rotate the knob clockwise until tight.
(X) with console mounting plate JJ. Reinstall the
four (4) screws (AA), through the plate and tighten. Visual Inspections. Inspect the unit for loose bolts, hardware,
knobs or pins and make sure the unit is level before beginning an
Tilt the console toward the seatback and align the
exercise session.
mounting holes in the console hinge cover (BB)
with the mounting holes found on the backside of Connect to Power. Plug the AC adaptor in an power outlet. Plug
the console. Reinstall the two Phillips fixing screws the other end into the input jack (HH).
(CC) and tighten.
9