Additive manufacturing and strategic technologies in advanced ceramics: a collection of papers presented at CMCEE-11, June 14-19, 2015, Vancouver, BC, Canada

228 Pages·2016·26.508 MB·English

by  Michaelis, Alexander, Ohji, Tatsuki, Shimamaura, Kiyoshi, Singh, Mrityunjay

Additive Manufacturing and
Strategic Technologies in
Advanced Ceramics
Additive Manufacturing and
Strategic Technologies in
Advanced Ceramics
Ceramic Transactions, Volume 258
A Collection of Papers Presented
at CMCEE-11,
June 14–19, 2015,
Vancouver, BC, Canada
Edited by
Kiyoshi Shimamura
Soshu Kirihara
Jun Akedo
Tatsuki Ohji
Makio Naito
Volume Editors
Mrityunjay Singh
Tatsuki Ohji
Alexander Michaelis
Copyright © 2016 by The American Ceramic Society. All rights reserved.
Published by John Wiley & Sons, Inc., Hoboken, New Jersey.
Published simultaneously in Canada.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form
or by any means, electronic, mechanical, photocopying, recording, scanning, or otherwise, except as
permitted under Section 107 or 108 of the 1976 United States Copyright Act, without either the prior
written permission of the Publisher, or authorization through payment of the appropriate per-copy fee to
the Copyright Clearance Center, Inc., 222 Rosewood Drive, Danvers, MA 01923, [phone], fax
[phone], or on the web at www.copyright.com. Requests to the Publisher for permission should
be addressed to the Permissions Department, John Wiley & Sons, Inc., 111 River Street, Hoboken, NJ
07030, [phone], fax [phone], or online at http://www.wiley.com/go/permission.
Limit of Liability/Disclaimer of Warranty: While the publisher and author have used their best efforts in
preparing this book, they make no representations or warranties with respect to the accuracy or
completeness of the contents of this book and specifically disclaim any implied warranties of
merchantability or fitness for a particular purpose. No warranty may be created or extended by sales
representatives or written sales materials. The advice and strategies contained herein may not be
suitable for your situation. You should consult with a professional where appropriate. Neither the
publisher nor author shall be liable for any loss of profit or any other commercial damages, including
but not limited to special, incidental, consequential, or other damages.
For general information on our other products and services or for technical support, please contact our
Customer Care Department within the United States at [phone], outside the United States at
[phone] or fax [phone].
Wiley also publishes its books in a variety of electronic formats. Some content that appears in print may
not be available in electronic formats. For more information about Wiley products, visit our web site at
www.wiley.com.
Library of Congress Cataloging-in-Publication Data is available.
ISBN: 978-1-119-23600-9
ISSN: 1042-1122
Printed in the United States of America.
10 9 8 7 6 5 4 3 2 1
Contents
Preface ix
ADDITIVE MANUFACTURING TECHNOLOGIES
Additive Manufacturing of Micro Functional Structures through 3
Diameter Variable Laser Stereolithography and Precursor
Sintering Heat Treatments
Soshu Kirihara
Stereolithographic Additive Manufacturing of Solid Electrolyte 11
Dendrites with Ordered Porous Structures for Fuel Cell
Miniaturizations
Soshu Kirihara
Processing of Thermoplastic Suspensions for Additive 19
Manufacturing of Ceramic- and Metal-Ceramic-Composites by
Thermoplastic 3D-Printing (T3DP)
U. Scheithauer, E. Schwarzer, A. Haertel, H.J. Richter, T. Moritz, and
A. Michaelis
Micro-Reactors Made by Lithography-Based Ceramic 31
Manufacturing (LCM)
U. Scheithauer, E. Schwarzer, G. Ganzer, A. Kornig, W. Beckert, E. Reichelt,
M. Jahn, A. Hartel, H. J. Richter, T. Moritz, and A. Michaelis
Functionally Graded Ceramic Based Materials using Additive 43
Manufacturing: Review and Progress
Li Yang, Hadi Miyanaji, Durga Janaki Ram, Amir Zandinejad, and Shanshan
Zhang
v
ADVANCED MATERIALS, TECHNOLOGIES, AND DEVICES FOR
ELECTRO-OPTICAL AND BIOMEDICAL APPLICATIONS
A Neutron Detector Based on Boron-10 Enriched Scintillating 59
Glasses
Dat Vu, Makena Dettmann, Victor Herrig, Luiz G. Jacobsohn,
Matthew W. Kielty, James Wetzel, Yasar Onel, and Ugur Akgun
Engineering Approach to Improve the Solid State Lighting 69
Characteristics with Translucent Poly Crystalline Alumina
Keiji Matsuhiro, Keiichiro Watanabe, Tsuneaki Ohashi, and
Tomokatsu Hayakawa
Single Crystal Fibers of Cladded Doped-YAG for High Power Laser 83
and Amplifier Applications
E. Gebremichael, B. Ponting, R. Magana, and G. Maxwell
Single Crystal Growth of Ferroelectric LaBGeO for Optical 97
5
Frequency Conversion Devices
Shintaro Miyazawa, Mitsuyoshi Sakairi, Junji Hirohashi, Makoto Matsukura,
Shunji Takekawa, and Yasunori Furukawa
The Growth of Potassium Tantalate Niobate (KTa Nb O ) Single 105
x 1-x 3
Crystal by Vertical Bridgman Method
Toshinori Taishi, Kazuya Hosokawa, Keigo Hoshikawa, Takahiro Kojima,
Junya Osada, Masahiro Sasaura, Yasunori Furukawa, and
Takayuki Komatsu
Growth of Y Al O Single Crystals via Edge-Defined Film-Fed 113
3 5 12
Growth Technique Using MO Crucibles
T. Tokairin, J. Hayashi, G. Villora, and K. Shimamura
MULTIFUNCTIONAL COATINGS FOR ENERGY AND
ENVIRONMENTAL APPLICATIONS
Nanoparticle Paste Injection into Gas-Flame Thermal Spray for 123
Speedy Ceramic Coating
Soshu Kirihara
Contribution to Electrochemical Oxidation of a Xanthene Dye onto 131
Cu O Thin Film Electrode
2
M. El hajji, A. Tara, Ph. Dony, O. Jbara, L. Bazzi, A. Benlhachemi, and
N. Kireche
Solution Precursor Plasma Sprayed Superhydrophobic Surface 141
Yuxuan Cai, Gisele Azimi, Thomas W. Coyle, and Javad Mostaghimi
vi · Additive Manufacturing and Strategic Technologies in Advanced Ceramics
Improvement of Interfacial Strength for Thermal Barrier Coatings by 149
Formation of Wedge-Like Thermally Grown Oxide
Kazuhiro Ogawa, Shun Hatta, and Hiroyuki Yamazaki
Experimental Production of Industrial Roller Coated by Hard 159
(cid:2)-Al O Film using Aerosol Deposition Process
2 3
Naoki Seto, Kazuteru Endo, Noriaki Honda, Nobuo Sakamoto,
Shingo Hirose, and Jun Akedo
NOVEL, GREEN, AND STRATEGIC PROCESSING AND
MANUFACTURING TECHNOLOGIES
Stereolithographic Additive Manufacturing of Ceramics Dendrites 167
to Modulate Energy and Material Flows
Soshu Kirihara
New Lightweight Kiln Furniture—Production Processes and 177
Properties
U. Scheithauer, T. Slawik, E. Schwarzer, F. Tscharntke, H.-J. Richter,
T. Moritz, and A. Michaelis
The Role of CALPHAD Approach in the Sintering of B C with SiC 185
4
as a Sintering Aid by Spark Plasma Sintering Technique
Mohammad Asadikiya, Christopher Rudolf, Cheng Zhang, Benjamin Boesl,
and Yu Zhong
POWDER PROCESSING TECHNOLOGY FOR ADVANCED CERAMICS
Effective Exfoliation of Laminated h–BN Particles by a Novel 195
Rotating Disk Method
Yuichi Tominaga, Daisuke Shimamoto, Kimiyasu Sato, Yusuke Imai, and
Yuji Hotta
COMPUTATIONAL DESIGN AND MODELING
Feasible and Reliable Ab InitioApproach to Computation of 207
Materials Relevant for Nuclear Waste Management
Piotr M. Kowalski, George Beridze, Yan Li, Yaqi Ji, Christoph Friedrich,
Ersoy a ıo lu, and Stefan Blügel
MATERIALS FOR EXTREME ENVIRONMENTS
Phase Evolution Phenomenon during Hot Pressing of the SHS 221
obtained Ti AlC Precursors Powders
3 2
L. Chlubny, J. Lis, Cz. Kapusta, D. Zientara, K. Chabior, and
P. Chachlowska
Author Index 229
Additive Manufacturing and Strategic Technologies in Advanced Ceramics · vii
Preface
The global challenges we face require innovative thinking and sustainable technol-
ogy to meet increased demands for energy, clean water, and infrastructure. Re-
search in materials, specifically ceramic materials, continues to provide solutions to
everyday challenges such as environmental protection, energy supply and genera-
tion, and healthcare. The 11th International Symposium on Ceramic Materials and
Components for Energy and Environmental Applications (11th CMCEE), held June
14–19, 2015 at the Hyatt Regency Vancouver in Vancouver, B.C., Canada, identi-
fied key challenges and opportunities for ceramic technologies to create sustainable
materials.
This Ceramic Transactions volume contains papers submitted from the follow-
ing seven symposia held in Track 4: Cross-Cutting Materials Technologies in Ad-
vanced Ceramics:
• Additive Manufacturing Technologies
• Advanced Materials, Technologies, and Devices for Electro-optical and
Biomedical Applications
• Multifunctional Coatings for Energy and Environmental Applications
• Novel, Green, and Strategic Processing and Manufacturing Technologies
• Powder Processing Technology for Advanced Ceramics
• Computational Design and Modeling
• Materials for Extreme Environments: Ultra-high Temperature Ceramics
(UHTCs) and Nanolaminated Ternary Carbides and Nitrides (MAX Phases)
After a peer-review process, 22 papers were accepted for inclusion in this pro-
ceedings volume. The editors wish to extend their gratitude and appreciation to all
the symposium co-organizers for their help and support, to all the authors for their
cooperation and contributions, to all the participants and session chairs for their
time and efforts, and to all the reviewers for their valuable comments and sugges-
tions. We also acknowledge the organization and leadership provided by the meet-
ing chairs, Mrityunjay Singh, Tatsuki Ohji, and Alexander Michaelis.
ix
We hope these proceedings will serve as a useful resource for researchers and
engineers working in the field of environmental science and technology.
KIYOSHISHIMAMURA, NIMS, Japan
SOSHUKIRIHARA, Osaka University, Japan
JUNAKEDO,AIST, Japan
TATSUKIOHJI, AIST, Japan
MAKIONAITO, Joining and Welding Research Institute, Osaka University, Japan
x · Additive Manufacturing and Strategic Technologies in Advanced Ceramics
Additive Manufacturing
Technologies