Table Of Contentइंटरनेट मानक
Disclosure to Promote the Right To Information
Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.
“जान1 का अ+धकार, जी1 का अ+धकार” “प0रा1 को छोड न’ 5 तरफ”
Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru
“The Right to Information, The Right to Live” “Step Out From the Old to the New”
IS/QC 300301 (1993): Fixed Capacitors for Use in Electronic
Equipment Blank Detail Specification: Aluminium
Electrolytic Capacitors with Non-Solid Electrolyte
Assessment Level E [LITD 5: Semiconductor and Other
Electronic Components and Devices]
“!ान $ एक न’ भारत का +नम-ण”
Satyanarayan Gangaram Pitroda
““IInnvveenntt aa NNeeww IInnddiiaa UUssiinngg KKnnoowwlleeddggee””
“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता हहहहै””ै”
Bhartṛhari—Nītiśatakam
“Knowledge is such a treasure which cannot be stolen”
IS QC 300301 :I992
IEC QC 300301 :19&i
Indinn Standard
FIXED CAPACITORS FOR USE IN
ELECTRONIC EQUIPMENT
Blank Detail Specification:
Alumin ium Electrolytic Capacitors with Non-Solid Electrolyte
Assessment Level E
NATIONAL POREWORD
This Indian Standard, which is identical with IX! Pub 384-4-!/QC 300301 ( 198.5 ) ‘Fixed
capacitors for use in electronic equipment - Part 4 : Blank detail specification: Aluminium
electrolytic capacitors with non-solid electrolyte, assessment level E’, issued by the Inter-
national ElectrotPchnical Commission was adopted by the Bureau of Indian Standards on the
recommendation of the Capacitors Sectional Committee ( LTD 15 ) and approval of the
Electronics and Telecommunication Division Council.
The text of the TEC standard has been approved as suitable for publication as Indian Standard
without deviations. Certain conventions are, however. not identical to those used in Indian
Standards. Attention is particularly drawn to the following:
Wherever the words ‘International Standard’ appear, referring to this standard, they should
be read as $Indian Standard’.
In the adopted standard, reference appears to certain International Standards for which Indian
Standards also exist. The corresponding Indian Standards which are to be substituted in their
place are listed below along with their degree of equivalence for the editions indicated:
International Standard Corresponding Indian Standard Degree of
Eq”uivalence
IEC Pub 384-l IS QC 300000 : 1988 Fixed capacitors for use Identical
QC 300000 ( 1982 ) in electronic equipment : Generic specifica-
tion
IEC Pub 384-4 IS QC 300300 : 1990 Fixed capacitors for Identical
QC 300300 ( 1985 ) use in electronic equipment : Sectional
specification : Aluminium electrolytic
capacitors with solid and non-solid
electrolyte. Selection of methods of test
and requirements
The concerned technical committee has reviewed the provisions of IEC Pub 410 referred in this
adopted standard and has decided that it is acceptable for use in conjunction with this
standard.
This standard is intended primarily for use under the IECQ system. A regular Indian Standard
for this component could be different, identical or similar to this standard.
Only the English language text in the International Standard has been retained while gnitpoda
it as Indian Standard.
As in the Original Standard, this Page is Intentionally Left Blank
ISQC 300301 : 1993
IEC QC 300301 : 1985
INTRODUCTION
Blank detail specification
A blank detail specification is a supplementary document to the Sectional Specification and
contains requirements for style and layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in accord-
ance with I E C specifications nor shall they so be described.
In the preparation of detail specifications the content of Sub-clause 1.4 bf the sectional
specification shall be taken into account.
The numbers between brackets on the first page correspond to the following information which
shall be inserted in the position indicated.
Identification of the detail specification
]I[ The “International Electrotechnical Commission” or the National Standards Organization
under whose authority the detail specification is drafted.
[2] The I E C or National Standards number of the detail specification, date of issue and any
further informatioh required by the national system.
[3] The number and issue number of the I E C or national Generic Specification.
[4] The I E C number of the blank detail specification.
Identifi:cation of’ the capacitor
[51 A short description of the type of capacitor.
PI Information on typical construction (when applicable).
Note. - When the capacitor is not designed for use in printed board applications, this shall be clearly stated in the
detail specification in this position.
[71 Outline drawing with main dimensions which are of importance for interchangeability and,‘or
reference to the national or international documents for outlines. Alternatively, this drawing
may be given in an appendix to the detail specification.
PI Application or group of applications covered and/or assessment level.
Note. - The assessment level(s) to be used in a detail specification shall be selected from the sectional specification,
Sub-clause 3.5.4. This implies that one blank detail specification may be used in combination with several
assessment levels, provided the grouping of the tests does not change.
191 Reference data on the most imljortant properties, to allow comparison between the various
capacitor types.
3
L.
ISQc 300301 : 1993
IEC QC 300301 : 1985
I EC 384-4-1-XxX PI
QC 300301-XXX
ELECTRONIC COMPONENTS OF ASSESSED QUALITY I E C 384-4-I [41
IN ACCORDANCE WITH: QC 300301
I t
[31 ALUMINIUM ELECTROLYTIC [51
CAPACITORS WITH
NON-SOLID ELECTROLYTE
Outline drawing: (see Table I)
(. angle projection)
[71
WI
Assessment level(s): E [81
(Other shapes are permitted within
I the dimensions givkn) Performance grade :
Information on the availability of components qualified to this
detail specification is given in the Qualified Products List.
[91
_.L _.
_I.-.._-.
ISQC 300301 : 1993
IEC QC 300301 : 1985
SECTION ONE - GENERAL DATA
1. General data
1.1 Recommended method(s) of mounting (to be inserted)
(See Sub-clause 1.4.2 of I E C Publication 384-4)
1.2 Dimensions
TABLE I
Dimensions (in millimetres or inches and millimetres)
Case size
reference PI L H d .
Notes I. - When there is no case size reference, Table I may be omitted and the dimensions shall be given in
Table IIA, which then becomes Table 1.
2. ~ The dimensions shall be given as maximum dimensions or as nominal dimensions with a toler-
ance.
1.3 Ratings aitd characteristics
Capacitance range (see Table IIA)
Tolerance on rated capacitance
Rated voltage (see Table IIA)
Category voltage (if applicable) (See Table IIA)
Climatic category
Rated temperature
Rated ripple current (see Table IIB)
Tangent of loss angl e (see Table IIB)
Leakage current
Impedance (if applicable) (see Table IIB)
Reverse voltage (if required)
Insulation resistance (if applicable)
TABLE IIA
Values of capacitance and of voltage related to case sizes
Rated voltage
Category voltage *
Case size Case size C&se size Case size
Rated capacitance
(in PF)
* If different from the rated voltage.
5
ISQC 300301 : 1993
IEC QC 300301 : 1985
TABLE IIB
Tangent of loss angle, impedance and rated ripple current
Tangent of loss Impedance (0) Rated ripple
UR cR
angle at “C, at . “C, . Hz current (A)
(V) (PF) HZ (if applicable) at “C, . . Hz
1.4 Related documents
Generic specification : I E C Publication 384-l (1982): Fixed Capacitors for Use
in Electronic Equipment. Part 1: Generic Specification.
Sectional specification : I E C Publication 384-4 (1985): Part 4: Sectional Specifi-
cation: Aluminium Electrolytic Capacitors with Solid or
Non-solid Electrolyte.
1.5 Marking
The marking of the capacitor and the package ;hall be in accordance with the require-
ments of I E C Publication 384-4, Sub-clause 1.6.
NOW.- The details of the marking of the component and package shall be given in full in the detail speciti-
cation.
1.6 Ordering iiformation
Orders for capacitors covered by this specification shall contain, in clear or in coded form,
the following minimum information :
a) Rated capacitance.
h) Tolerance on rated capacitance.
/c
Rated d.c. voltage.
d) Number and issue reference of the detail specification and style reference.
6
