(CNC Current) Addendum for 15" Systems Series 30i/31i/32i

232 Pages·2005·2.42 MB·English

GE Fanuc Automation
Computer Numerical Control Products
Addendum for 15" Systems
Series 30i/31i/32i
Common to Lathe System/Machining
Center Systems User’s Manual,
GFZ-63944EN/02
GFK-2411
August 2005
GFL-002
Warnings, Cautions, and Notes
as Used in this Publication
Warning
Warning notices are used in this publication to emphasize that hazardous voltages,
currents, temperatures, or other conditions that could cause personal injury exist in this
equipment or may be associated with its use.
In situations where inattention could cause either personal injury or damage to equipment,
a Warning notice is used.
Caution
Caution notices are used where equipment might be damaged if care is not taken.
Note
Notes merely call attention to information that is especially significant to understanding and
operating the equipment.
This document is based on information available at the time of its publication. While efforts
have been made to be accurate, the information contained herein does not purport to cover all
details or variations in hardware or software, nor to provide for every possible contingency in
connection with installation, operation, or maintenance. Features may be described herein
which are not present in all hardware and software systems. GE Fanuc Automation assumes no
obligation of notice to holders of this document with respect to changes subsequently made.
GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory
with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or
usefulness of the information contained herein. No warranties of merchantability or fitness for
purpose shall apply.
The following are trademarks of GE Fanuc Automation, Inc.
Alarm Master Genius ProLoop Series Six
CIMPLICITY Helpmate PROMACRO Series Three
CIMPLICITY 90–ADS Logicmaster PowerMotion VersaMax
CIMSTAR Modelmaster PowerTRAC VersaPoint
Field Control Motion Mate Series 90 VersaPro
GEnet PACSystems Series Five VuMaster
Proficy Series One Workmaster
©Copyright 2005 GE Fanuc Automation North America, Inc.
All Rights Reserved
Chapter 8
Data Input / Output
(15”Display)
To be used in place of Operation Section, Chapter 8
Series 30i/31i/32i User Manual (GFZ-63944EN/02),
for S-30i/31i/32i systems using 15” Display.
Chapter 8 in GFZ-63944EN/02 should be used for
S-30i/31i/32i systems using 10.4” display.
This page intentionally blank.
OPERATION 8.DATAINPUT/OUTPUT(15inch)
8
DATA INPUT/OUTPUT
By using the memory card interface on the left side of the display,
information written in a memory card is read into the CNC and
informationiswrittenfromtheCNCtoamemorycard.
Thefollowingtypesofdatacanbeinputandoutput:
1. Program
2. Parameter
3. Offsetdata
4. Pitcherrorcompensationdata
5. Three-dimensionalerrorcompensationdata
6. Custommacrocommonvariable
7. Workpiececoordinatesystemdata
8. Operationhistorydata
9. Toolmanagementdata
The above data can be input and output on the screens used for
displayingandsettingthedataandontheALLIOscreen.
-1-
8.DATAINPUT/OUTPUT(15inch) OPERATION
8.1
INPUT/OUTPUT ON EACH SCREEN
Various types of data including programs, parameters, offset data,
pitch error compensation data, three-dimensional error compensation
data, custom macro common variables, workpiece coordinate system
data, operation history data, and tool management data can be input
andoutputusingoperationscreens.
-2-
OPERATION 8.DATAINPUT/OUTPUT(15inch)
8.1.1 Inputting and Outputting a Program
8.1.1.1 Inputting a program
The following explains how to input a program from a memory card
to the memory of the CNC by using the program editing screen or
programdirectoryscreen.
Inputting a program
Procedure
1 Makesuretheinputdeviceisreadyforreading.
2 Pressthefunctionkey PROG .
3 Press the vertical soft key [PROGRM] or [FOLDER], and then,
programscreenorprogramfolderappears.
4 Press the EDIT switch on the machine operator(cid:182)s panel or enter
stateemergencystop.
5 Pressthehorizontalsoft key + (continuous menukey)untilthe
horizontalsoft key[READ]appears,thenpressthehorizontalsoft
key[READ].
6 Type the name of the file that you want to input, and press the
horizontalsoftkey[FSET]. Also,typethenameoftheprogram
thatyouwanttoinput,andpressthehorizontalsoftkey[PSET].
If the input file name is omitted, default input file name
(cid:179)ALL-PROG.TXT(cid:180)isassumed.
Seethefollowingtableincase,[FSET]and[PSET]isomitted.
7 Pressthehorizontalsoftkey[EXEC].
This startsreadingtheprogram, and(cid:179)INPUT(cid:180)blinks inthelower
right part of the screen. When the read operation ends, the
(cid:179)INPUT(cid:180)indicationdisappears.
Tocanceltheinput,pressthehorizontalsoftkey[CAN].
[FSET] [PSET] Inputfilename Inputprogram Inputprogramname
All programs in an File name when a save
(cid:177) (cid:177) ALL-PROG.TXT
ALL-PROG.TXT operationisperformed
Initial program in an Program name set for the
(cid:177) (cid:1636) ALL-PROG.TXT
ALL-PROG.TXT softkey[PSET]
File name set for the soft All programs in a file set File name when a save
(cid:1636) (cid:177)
key[FSET] forthesoftkey[FSET] operationisperformed
File name set for the soft Initialprograminafileset Program name set for the
(cid:1636) (cid:1636)
key[FSET] forthesoftkey[FSET] softkey[PSET]
(cid:1636) :INPUT
(cid:177) :BLANK
-3-
8.DATAINPUT/OUTPUT(15inch) OPERATION
8.1.1.2 Outputting a program
A program stored in the memory of the CNC unit is output to a
memorycard.
Outputting a program
Procedure
1 Makesuretheoutputdeviceisreadyforoutput.
2 Pressthefunctionkey PROG .
3 Press the vertical soft key [PROGRM] or [FOLDER], and then,
programscreenorprogramfolderappears.
4 Press the EDIT switch on the machine operator(cid:182)s panel or enter
stateemergencystop.
5 Pressthehorizontalsoftkey + (continuous menu key)untilthe
horizontal soft key [PUNCH] appears, then press the horizontal
softkey[PUNCH].
6 Typethe name of theprogramthat you want to output, and press
the horizontal soft key [P SET]. Also, typethe name of thefile
thatyouwanttooutput,andpressthehorizontalsoftkey[FSET].
If you type (cid:179)O-9999(cid:180) or nothing, all NC programs in foreground
folderareoutputto(cid:179)ALL-PROG.TXT(cid:180).
Seethefollowingtableincase,[FSET]and[PSET]isomitted.
(For details of foreground folder and changing the foreground
folder,refertoII-12.1.3andIII-11.6)
7 Pressthehorizontalsoftkey[EXEC].
This starts outputting the program, and (cid:179)OUTPUT(cid:180) blinks in the
lowerrightpartofthescreen. Whenthereadoperationends,the
(cid:179)OUTPUT(cid:180)indicationdisappears.
Tocanceltheoutput,pressthehorizontalsoftkey[CAN].
[FSET] [PSET] Outputfilename Outputprogram
All NC programs displayed on
(cid:177) (cid:177)or(O-9999) ALL-PROG.TXT
programfolderofforeground
Program name set for the soft key Aprogramstored inCNC memory
(cid:177) (cid:1636)
[PSET] setforthesoftkey[PSET]
Filenamesetforthesoftkey All NC programs displayed on
(cid:1636) (cid:177)or(O-9999)
[FSET] programfolderofforeground
Filenamesetforthesoftkey Aprogramstored inCNC memory
(cid:1636) (cid:1636)
[FSET] setforthesoftkey[PSET]
(cid:1636) :INPUT
(cid:177) :BLANK
-4-
OPERATION 8.DATAINPUT/OUTPUT(15inch)
8.1.2 Inputting and Outputting Parameters
8.1.2.1 Inputting parameters
ParameterisloadedintothememoryoftheCNCfromamemorycard.
Theinputformatisthesameastheoutputformat. Whenaparameter
is loaded which has the same data number as a parameter already
registered in the memory, the loaded parameter replaces the existing
parameter.
Inputting parameters
Procedure
1 Makesuretheinputdeviceisreadyforreading.
2 Pressthefunctionkey OFFSET .
SETTING
3 Press the vertical soft key [NEXT PAGE] until the vertical soft
key [SETTING] appears, then press the vertical soft key
[SETTING].
4 Press the MDI switch on the machine operator(cid:182)s panel or enter
stateemergencystop.
5 Enter 1inresponsetotheprompt for (cid:179)PARAMETERWRITE(cid:180)in
settingdata.
AlarmSW0100appears.
6 Pressthefunctionkey SYSTEM .
7 Press the vertical soft key [NEXT PAGE] until the vertical soft
key [PARAMETER] appears, then press the vertical soft key
[PARAMETER].
8 Press the EDIT switch on the machine operator(cid:182)s panel or enter
stateemergencystop.
9 Pressthehorizontalsoftkey[READ].
10 Typethenameofthefilethatyouwanttoinput.
If the input file name is omitted, default input file name
(cid:179)CNC-PARA.TXT(cid:180)isassumed.
11 Pressthehorizontalsoftkey[EXEC].
This starts reading the parameter, and (cid:179)INPUT(cid:180) blinks in the
lowerrightpartofthescreen. Whenthereadoperationends,the
(cid:179)INPUT(cid:180)indicationdisappears.
Tocanceltheinput,pressthehorizontalsoftkey[CAN].
12 Pressthefunctionkey OFFSET .
SETTING
13 Press the vertical soft key [NEXT PAGE] until the vertical soft
key [SETTING] appears, then press the vertical soft key
[SETTING].
14 Press the MDI switch on the machine operator(cid:182)s panel or enter
stateemergencystop.
15 Enter 0inresponsetotheprompt for (cid:179)PARAMETERWRITE(cid:180)in
settingdata.
16 TurnthepowertotheCNCbackon.
-5-
8.DATAINPUT/OUTPUT(15inch) OPERATION
8.1.2.2 Outputting parameters
Allparametersareoutputintheoutputformatfromthememoryofthe
CNCtoamemorycard.
Outputting parameters
Procedure
1 Makesuretheoutputdeviceisreadyforoutput.
2 Pressthefunctionkey SYSTEM .
3 Press the vertical soft key [NEXT PAGE] until the vertical soft
key [PARAMETER] appears, then press the vertical soft key
[PARAMETER].
4 Press the EDIT switch on the machine operator(cid:182)s panel or enter
stateemergencystop.
5 Pressthehorizontalsoftkey[PUNCH].
6 Typethefilenamethatyouwanttooutput.
If the file name is omitted, default file name (cid:179)CNC-PARA.TXT(cid:180)
isassumed.
7 Pressthehorizontalsoftkey[EXEC].
Thisstartsoutputtingtheparameter,and(cid:179)OUTPUT(cid:180)blinks inthe
lowerrightpartofthescreen. Whenthereadoperationends,the
(cid:179)OUTPUT(cid:180)indicationdisappears.
Tocanceltheoutput,pressthehorizontalsoftkey[CAN].
Explanation
- Suppressing output of parameters set to 0
When bit 1 (PRM) of parameter No. 0010 is set to 1, and [EXEC] is
pressed,thefollowingparametersarenotoutput:
Otherthanaxistype Axistype
Parameterforwhichallbitsare Parameterforanaxisforwhich
Bittype
setto0. allbitsaresetto0.
Parameterforanaxisforwhich
Valuetype Parameterwhosevalueis0.
thevalueis0.
-6-